Hot sale reasonable price Skirting board style JJ-A07-2 for Hongkong Importers
Hot sale reasonable price Skirting board style JJ-A07-2 for Hongkong Importers Detail:
Product detail pictures:
Persisting in "High quality, Prompt Delivery, Competitive Price", we have established long-term cooperation with clients from both overseas and domestically and get new and old clients' high comments for Hot sale reasonable price Skirting board style JJ-A07-2 for Hongkong Importers, The product will supply to all over the world, such as: Jordan , Norway , Burundi , In order to meet the increasing requirement of customers both home and aboard, we will keep carrying forward the enterprise spirit of "Quality, Creativity, Efficiency and Credit" and strive to top the current trend and lead fashion. We warmly welcome you to visit our company and make cooperation.
Complete bathroom shower install. A pre slope, vinyl shower liner, cement board, recesses niche, waterproofing, porcelain tile floor, and grouting. A pre pitch or pre slope under a shower pan liner is an essential part of a successful tile shower installation. A pre slope is the base under the shower pan liner which is pitched so that the any water that manages to get into the shower base can be directed to the weep holes in the three piece drain and out of the liner. If a pre slope is not installed under the liner then any water that filters into the base of the shower will remain there. To install a pre slope first a sheet of tar paper is placed on the subfloor followed by a metal lath to reinforce the mud, especially at its thinnest point at the drain. The deck mud is then shaped so that there is a slope of ¼” per foot sloping towards the drain. The part of the base furthest away from the drain will be higher than the drain, so as to create a positive pitch towards the drain. When installing a vinyl liner for the pan of a shower floor, it is imperative that any penetrations to secure the liner be above the level of the shower curb. Also the folds at the corners of the shower should always be done without cutting the liner lower than the shower curb. I do not install dam corners on the curb, because I apply a liquid waterproofing membrane on the surface of the entire shower stall, or at the very least the curb will be thoroughly waterproofed to avoid leeks in this critical area if this step is to be omitted, the dam corners should be used. The silicone bead at the drain where the liner is clamped to the 3 piece drain should always be applied, do not skip this step. How to install mud in a shower pan for a tile shower stall. When installing a tile shower, whether it be ceramic, marble travertine or any other tile product, a mud base will be required. Mud also known as deck mud, is a mixture of sand and Portland cement mixed to a ratio that will create a solid foundation for the tile which will be installed on it. The deck mud is mixed with water to a dump consistence which will allow the deck mud to hold its shape when pressed into a ball. The mud must be pitcher towards the drain so that a slope of at least ¼” per foot is achieved. The ratio of sand and Portland cement is usually 4:1 or 5:1. I usually use “Quikrete” sand topping mix, which as far as I know, has a ratio which is a little richer than needed, but is suitable for a shower pan. The method I employ to install my mud in shower pan, is to create a level and flat perimeter around the base of the shower walls which is at the correct height in relation to the drain, and then fill the middle part of the shower pan screeding down to the drain with the proper pitch. The mud is shaped with a wooden trowel, steel trowel, level and other pieces of straight wood lengths cut to the required lengths. In this video I demonstrate the technique I use to install a shower mud pan base. There are other methods that can be used, but this is the way I have installed hundreds of shower bases. How to cut and install cement backer board for ceramic wall tile. When installing a cement backer board it is important to use the correct kind of screw. Drywall screws are not to be used to install the cement board, due to the composition of the backer board an uncoated screw will deteriorate over time and compromise the integrity of the tile installation. A screw that has been coated or galvanized must be used. A screw should be placed every 8″, there is going to be a lot of weight when the tile is installed so an adequate number of fasteners should be used. To cut the board to the correct size a simple utility knife is all that is needed. Score the board with the blade of the knife a few times, and then bend the board back until it snaps, complete the cut by running the knife along the cut from the opposite side. A simple key hole saw can be used to make holes for shower valves and escutcheons. How to build a recessed niche in a shower. First step is to determine where the niche is going to be placed in relation to the tile, how big to make it and the number of shelves. Once the location is set, it is time to draw precise guidelines on the backer board to follow while cutting the hole in the backer board. Once the hole is cut, do not dispose of the piece of board removed to make the hole, it can be used for the back part of the niche. Install a piece of lumber at the top and bottom edge of the cutout and the sides of the niche. Install your backer board on the top, bottom sides and back of the niche area and thoroughly waterproof the entire niche.
This video contains affiliate links, which means I will receive a small commission if you click on the product link.
Products available at
Testing machine for producing precast lightweight concrete hollow core wall panels.
Smooth surface,high compactness,Rapid extrusion and forming
For more details, contact us
Henan Victory Industrial co.,Ltd
By Ivy from Iran - 2015.09.21 11:01
The sales manager has a good English level and skilled professional knowledge, we have a good communication. He is a warm and cheerful man, we have a pleasant cooperation and we became very good friends in private.
By June from Uzbekistan - 2015.06.18 19:26